Mill Axis Router

CNC Kit 4 Axis Nema23 Stepper Motor EMA2-050D56 Stepper Driver For Mill/Router

CNC Kit 4 Axis Nema23 Stepper Motor EMA2-050D56 Stepper Driver For Mill/Router

CNC Kit 4 Axis Nema23 Stepper Motor EMA2-050D56 Stepper Driver For Mill/Router

CNC Kit 4 Axis Nema23 Stepper Motor EMA2-050D56 Stepper Driver For Mill/Router. 4 Axis Kit for CNC DIY.

M Stepper Motors + 136V 15A Switching Power Supply. The 5 axis breakout board in this kit is specially designed for CNC single axis stepper driver controller. Maximum 5 pcs can be connected. In the market, such as ENGMATE series, M542, M542H, MA560, MA860H, 2M542, 2M982, DM542(A), DM860(A) etc.. It can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc. The stepper driver board controller in kit is a high performance microstepping driver adopting of 32-bit DSP, pure sine wave subdivision technology. With this technology and the self-adjustment technology (self-adjust current control parameters) for different motors, the drive motors can run with less noise, lower heating, smoother movement and have better performances at higher speed than most of the drivers in the market. In short, you will get more benefits from the Kit on CNC work, especially extra-low motor noise offers excellent quietness. We have been fulfilling CNC Motion Control needs for over 10 years to support any project you may have.

Stepper motors and drivers from ENGMATE. Are with high quality for stable and durable usage. Upgraded circuit, work more peacefully and steady than the previous version.

To get power: 5V DC power supply or USB port to get power from PC directly. Signal processing, smooth signal transmission, powerful anti-jamming. Interface to define the Limit, Emergence-Stop, Midpoint-Alignment, Cutter-Alignment, etc. Accessed by the spindle motor or the air pump, water pump, etc.

Visually display the working condition of the stepper driver controller. Extra-low motor noise offers excellent quietness. With 7 stalls output current setting. Adoption of 32-bit DSP, pure sine wave subdivision technology. Low-vibration and low temperature rising.

With 15 stalls microstep subdivision setting. Automatic half-current reduction as long as switching off SW4 when motors stop. Internal optical isolation, pulse input frequency up to.

Short-voltage, over-voltage, over-current and short-circuit protection, protect the motors, driver from being damaged. Suitable for 2-phase and 4-phase Hybrid stepper motors.

High torque, more smooth movement. High efficiency, energy-saving, low noise and low vibration.

High start torque, low start current and reliable performance. Simple 4 wires ensure easier wiring, installation and maintenance. High efficiency, high reliability, low cost.

PWM control and regulation, insure the steady and precise output voltage. Over-temperature protection: built-in a powerful fan for cooling. 100% full load burn-in test. Over current, over voltage, short circuit.

Low output ripple and yawp. Suitable for a variety of small sized automation equipment and instruments.

For any small-and-medium automatic equipment with CNC controller, such as engraving machine, plasma cutting machine, milling machine, foam cutting machine, lathes, laser cutting machine etc.. For other industrial application, such as 3D printer, medical instruments, stage light equipment, robot, music fountain etc.. Electrical Properties of 5Axis Breakout Board (ambient temperature Tj = 25°C). 5V DC via power adapter or directly get power from PC via USB port. Pulse + Direction + Enable Signal Control.

2 Phase, 3 Phase, 4 Phase Microstep Driver EMA2-050D42/ EMA2-070D56/ EMA2-080D72/ EMA2-220A80 etc. Natural Cooling or Fan Forced cooling. Avoid dust, oil fog, corrosive gas. 540W 36V 15A Switching Power Supply 110/220V Switchable. 110VAC/ 220VAC±20% (selected by switch).

Australia, New Zealand, South Asia, East Asia. South America, Other Countries/ Regions. Usually, we dispatch your order within. However, 95%+ parcels are delivered within the reference time.

Please do contact and confirm with us BEFORE placing order. If you receive a not-as-described e. We will arrange a replacement as soon as the case is confirmed. All qualified return/replacement must be guided by us. We may not accept your return without communication in advance.

By placing an order, you acknowledge that you have accepted the terms and conditions of sale. The item "CNC Kit 4 Axis Nema23 Stepper Motor EMA2-050D56 Stepper Driver For Mill/Router" is in sale since Tuesday, October 19, 2021.

This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "xories" and is located in HK. This item can be shipped worldwide.

  • Brand: Generic
  • MPN: 10103230112100600
  • Model: 4 axis Nema23 Kit
  • Application: Support Software Mach3, Linuxcnc, KCam4, etc
  • Modification Description: Holding Torque 1.96N.m (278oz-in)
  • Input Voltage: DC 36V 15A
  • Number Of Axes: 4

CNC Kit 4 Axis Nema23 Stepper Motor EMA2-050D56 Stepper Driver For Mill/Router