CNC Kit 4Axis Nema23 Stepper Motor M335 Stepper Driver For Mill/Router/Engraving. 4 x 3.5A 30VDC M335 Microstep Drivers + 1 x 5-axis Breakout Board 4 x Nema23 1.26Nm/175 Oz-in Stepper Motors + 1 x 24V 15A Switching Power Supply. The 5-axis breakout board is specially designed for the CNC 2-phase stepper driver controller. The breakout board uses high-performance three-state driver 74HC244 and Schmitt inverter 74HC14.
The amplified, rectified, filtered input signals make the drive capability of the output signals more stable and stronger. With this 5-axis breakout board, any 1-5 Microstepper driver controllers can be directly controlled by PC via the MACH3, KCAM4, WinPc Light etc.The M335 is a high performance microstepping driver with low price. The M335 adopts single-chip PWM bipolar sinusoidal chopper to ensure low vibration and high efficiency. It is suitable for driving 2-phase and 4-phase hybrid stepping motors, so the Nema16, Nema17, Nema23 stepper motors with a 0.5A-3.5A current will be suitable. In short, you will get more benefits from the Kit on CNC work. All the signals are opto-isolated. Which can protect your computer.
For the Limits, Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V, and with anti-reverse function. One relay output control interface. Accessed by the spindle motor or the air pump, water pump, etc.
For inverter to control the spindle speed. Low cost, Non-creeping phenomenon under low speed.
Low noise and non-resonant region. Suitable for 2-phase and 4-phase motors.
High speed optoelectronic isolation signal input. 1, 2, 8, 16 adjustable micro step control for more accurate and smoother motor running. Suitable for a variety of small sized automation equipment and instruments. Suitable for a wide range of stepping motors, from NEMA size 16/17/23.
12-24V DC power supply for Nema 16/17 stepper motors. 24-30V DC power supply for Nema 23 stepper motors.
High (= 30V) voltage will burn out the chips or stepper motors!!! Please be careful in choosing power supply. Output current of the power supply can be calculated by the following formula.
Output current = Rated current of your stepper motors x quantity + 2A. If the supply current is too low for the drivers, it will easily burn the drivers. Please SHUT DOWN the power before you plug or unplug the connectors and adjust the DIP Switches to avoid burning up the board. Electrical properties of Breakout boardambient temperature Tj = 25?
Get power from PC via USB port and 12-24V power supply(optional). Pulse and Direction Signal Control. Electrical Specifications Of M335 Microstepper Driver. 0.5A 3.5A (Peak). Pulse + Direction + Enable Signal Control (Single-Chip PWM Bipolar Sine Chopper).Operationg Environment & Other Specifications Of M335 Microstepper Driver. Natural Cooling or Fan Forced cooling. Avoid dust, oil fog, corrosive gas.
0 °C 50°C (32°F 122°F). 20 °C 125°C (-4°F 257°F). Specifications of Switching Power Supply. 100-120VAC and 200-240VAC by Switch.Single Shaft (Diameter:6.35mm; Length:21mm). (May depart from other stock location). Require that the item should be delivered within a certain time. It is not guaranteed that parcel should arrive within the time stated above. However, 95%+ parcels will be delivered within the reference time. We will help you to track them. If you receive a not-as-described e. We will arrange a replacement as soon as the case is confirmed. All qualified return/replacement must be guided by us.
We may not accept your return without communication in advance. By placing an order, you acknowledge that you have accepted the terms and conditions of sale.The item "CNC Kit 4Axis Nema23 Stepper Motor M335 Stepper Driver For Mill/Router/Engraving" is in sale since Thursday, September 12, 2019. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "savebase" and is located in Los Angeles. This item can be shipped worldwide.