Mill Axis Router

3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling

3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling
3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling

3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling

CNC Spindle Motor & Tool Parts. Note : If you need the dual shaft stepper motor , please leave us messages. 3 x MA860H Sumtor step motor drive 2ph 24110VDC AC18-80V 27.8A. 3 x 86BYG 2ph Hybrid stepper motor 86HS9860A4 L 98mm 4-lead 6A 6.5NM 1.8 degree.

Switching Power Supply 400W 60V 6.7A for CNC S-400-60. 1 x 5 Axis CNC Breakout Board Interface For Stepper Motor Driver (free offer). 1 x DB25 Parallel Cable & USB Power Cable. Shaft Type: double-sided milling flat 1mm. Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal; 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode(pulse/pulse) , this input represents clockwise (CW) pulse. Active at high level or low level (set by inside jumper J1 & J2).

For reliable response, pulse width should be longer than 1.5? Series connect resistors for current-limiting when+12V or +24V used. The same as DIR and ENA signals. DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside jumper J1 & J2), this signal is counter-clock (CCW) puls. For reliable motion response, DIR signal should be ahead of PUL signal by 5?

4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that motion direction is also related tomotor-driver wiring match. Two wires for a coilto the driver will reverse motion direction.

Enable signal: This signal is used for enabling/disabling the driver. High levelNPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.

For enabling the driver and low level fordisabling the driver. Power supply, 1880 VDC or 24110VDC, Including voltage fluctuation and EMF voltage.

Input voltage: AC110-230V (supports 110V has a pull switch). Output voltage: DC60V 6.7A.

5 axis CNC Breakout Board. Maximum support 5-axis stepper motor driver controllers. Compatible with MACH3, Linux CNC (EMC2) etc.

USB power supply and peripherals powered phase are separated to protect computer security. All the signals are opto-isolated which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment etc. Wide input voltage range: 12-24V, and with anti-reverse function. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc. Output 0-10V analog voltage for inverter to control the spindle speed.

USB port from PC or 12-24V power supply(optional). Pulse and Direction Signal Control. Please learn import duty to your country in details , and please leave us message about the invoice amount when place order to avoid the high import duty. If you need any CNC parts or repairs, welcome to contact me, we will try our best to help you.

The item "3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling" is in sale since Tuesday, June 2, 2015. This item is in the category "Business & Industrial\Automation, Motors & Drives\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "vipwindows_168" and is located in Shenzhen. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

  • Brand: Sumtor
  • Model: 3-MA860H-86HS9860A4
  • Country/Region of Manufacture: China
  • Stepper motor drive: 2ph 24~110VDC AC18-80V 2~7.8A
  • Stepper motor: Nema 34
  • Holding torque: 6.5Nm 920oz.in
  • Rated Current: 6A
  • Power supply: 400W 60V 6.7A
  • Application: CNC Router Lathe
  • MPN: Does not apply
  • UPC: Does not apply


3Axis Nema34 6.5Nm Stepper Motor Driver Kit 920oz. In 2phase CNC Router Milling