Mill Axis Router

3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control

3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control
3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control

3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control

3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control+ER11 Collet. CNC Laser machine kit (without laser). 10 x 20°0.1mm drill bits. 1 x Set of allen wrench.

(0.5W, 2.5W, 5.5W). Ps:because ER11 shank accuracy is very high, so the hole is small, therefore. Need to be heated before installing the shank to be fitted. Body used profiles and plastic, small size, light weight, USB interface, GRBL control system, learning, entry preferred. Can use carving knife, but also can use laser engraving. Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the like material. Spindle : 775 spindle motor (12-36V). Step motor : Fuselage length 34MM, Current 1.33A, 12v. Power supply : 24V 5.6A.

Support System: Windows XP / Win 7 / Win 8 / Win 10 / Linux. Drill bits: tip 0.1mm , 20 degree , diameter3.175mm. Laser: 500mw 405nm, 12v / 2500mw 450nm, 12v / 5500mw 450nm, 12v. GRBL 0.9J, USB port cnc engraving machine control board, 3 axis control. Master chip: atmel 328P (arduino nano).

Spindle drive chip: MOSFET (recommendation 1236V, current : within 10A). Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57).

Power Interface: 5.5-2.5mm DC interface. Manually control: manually adjust X, Y, Z axis location as engraving starting point, manually open or close spindle, manully open or close cooling fan. File engraving: after off-line controller save file, it can connect the GRBL control board and process engraving, no need to connect PC computer.

Save file: after the off-line controller connect PC, it will be recognized as USB, large capacity storage device, can access engraving file directly. SD shows it is SD card condition, turn on power supply after insert SD card, otherwise, it won't work. SD card capacity 4G could be recognized. Press X- or X+ button to switch. Control Press confirmation button to access manually controlling page.

File Press confirmation button to access file page. Set Press confirmation button to access setting page. On the off-line controller, buttons control corresponding actions. SPN is spindle controlling, should press SPIN.

Fan is fan controlling, should press SMOD. Note: To exit this page, should press back button longly. After exit, save the current location as engraving starting point X0Y0Z0. Note: system can recognize max 100 available files one time.

Tap could be recognized not support files with long name. Press Y+ or Y- to choose files need to be engraved, press confirmation button to access engraving page. Press ok to start engraving.

If you want to stop during engraving, press back button longly, then back to the file selection page machine will not stop at once, as GRBL controller has already saved a part of G code, will stop after carry out completely. The left words show the machine moving distances every time you press the button on the condition of manually controlling, press Y+ or Y- to choose, default 1mm each time.

The right words show Communication baud rate setting, default 9600. After setting, press confirmation button to save, then press back button to exit setting page. Note: the setting parameters can not be saved on the condition of electricity outage, it will be default value when turn on next time. The item "3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control" is in sale since Monday, December 24, 2018. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Woodworking Equipment\Routers".

The seller is "powace08" and is located in Changzhou,Jiangsu. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.

  • Drive: Stepper motor
  • Type: Desktop cnc router
  • laser: Support laser
  • System requirements: windows XP SP3, win7, win8, win10.

  • CNC or Not: CNC
  • Model: 3018
  • Country/Region of Manufacture: China
  • Collet: ER11 Collet
  • Port: USB port
  • Voltage: 220V
  • Axis: 3 Axis
  • Spindle: 775spindle motor(12-36V) 24V:7000r/min 36V:9000r/m
  • MPN: Does not apply
  • Brand: RATTM MOTOR
  • Support software: Grbl Control


3 Axis CNC 3018 Mini Router PVC PCB Wood Cutting Milling Machine+Offline Control