Mill Axis Router

1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A

1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A
1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A
1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A
1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A
1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A
1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A
1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A

1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A

Great News from Longs motor! 57BLF03 Nema23 Brushless DC motor for car 3Phases, 188W/24V 3000rpm LONGS router.

1pc Brushless DC Motor Driver BLDC-8015A. 5000RPM peak Speed, 80VDC, 3phases. Brushless DC motor driver BLDC-8015A. Speed/Current alike close loop technology, smooth rotation. Smooth torque output within speed range 8000 rpm Max. Potentiometer adjust / Analog input. Keep away from oil, dust, and acid gas. Normally Linear Power Supply applied. Ripple voltage higher than 50V may damage driver.

The output current of LPS shall be 60. More than that of driver.

In case of switching power supply(strongly recommended)applied, please pay attention to the current shall meet motors current. Attention: incorrect connection may cause driver damaged.

Speed regulation choice(RV ; AVI). Setup speed by potentiometer (RV). The dipswitch SW2 must be ON status to enable this function. CW rotate the potentiometer will increase speed. Setup speed by analog input (AVI).

The dipswitch SW2 must be OFF status to enable this function. 5V voltage or PWM signal from controller. AVI terminal with input resistance of 100K. Only one of above two modes can be used to adjust speed (another mode shall be enabled).

Once AVI terminal applied, (RV) potentiometer shall be CCW turned to Min. PWM signal are 5V TTL level.

ENBL terminal is applied to control motor Run/Stop. Optical coupler short circuit make motor run, it open circuit make motor stop. F/R terminal is applied to shift motor rotate direction, common positive terminal is.

Motor run in CCW when optical coupler is short circuit, motor run in CW when optical coupler is open circuit. Dont change the connection sequence of phase wires of motor to shift rotate direction. BRK terminal applied to stop rotation quickly. Motor will stop normally within 50ms.

But inertia of load cant exceed 2 times of motor inertia, otherwise brake will cause driver alarm. Time of acceleration and deceleration must be put into controller in case of too big load inertia. And please dont use brake function in such condition.

The optical coupler short circuit will brake motor. Optical coupler open circuit release motor to run. Dipswitch SW1 can be setup to fit motors with different electrical angel.

They are in opposite rotation direction. 60°or 300°hall signal, they are in opposite rotation direction. Pulse generated by driver are proportioned with motor speed, isolated O. Output it can be increased to be a random level. 6 multiple frequency processed output.

Driver will enter protection mode and stop motor running in case of OVER CURRENT, OVER VOLTAGE, SHORT CIUCUIT, MOTOR STALL arise. LED on driver will be light, and ALM signal will be available. High voltage is not permitted for big inertia motor, as it may cause run/stop frequently and over voltage alarm. Circuit of this function refer to pic. Make sure correct connection to motor leads. REF- are for hall power supply. Make sure correct connection to halls. Vout, Vout suggested to be AC21.

Capacity of transformer shall be decided by motors current. Attentiondont change the connection sequence of phase wires of motor to shift rotate direction. The item "1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A" is in sale since Monday, March 4, 2019. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\General Purpose Motors". The seller is "steppermotor0322" and is located in California.

This item can be shipped to North, South, or Latin America, all countries in Europe, China, Japan, Australia, South Korea, Indonesia, Taiwan, Thailand, Hong Kong, Israel, New Zealand, Philippines, Singapore, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Malaysia, Bangladesh, Brunei darussalam, Egypt, Jordan, Cambodia, Macao, Pakistan, Viet nam, South africa, Sri lanka, Maldives, Oman, Reunion.

  • warranty: 12 months
  • Non-Domestic Product: No
  • Model: 57BLF03
  • Modified Item: No
  • Country/Region of Manufacture: China
  • Custom Bundle: No
  • MPN: Does Not Apply
  • Brand: Longs Motor


1Axis 57BLF03 Brushless DC Motor Nema23 188W 24V 3000RPM Router Mill DRIVE 8015A